All Activity

Hey! I know this thread is a bit old, but since it’s one of the most viewed feature requests here, felt like it’s worth bringing it back post 1.0 release (and kudos to the team for the release 👏). Any updates on this?

Yup. Unfortunately one of the packages that HexOS local depends on (bun) requires these CPU features (for now at least).

Contains the number of occurrences where the controller detected an unrecovered data integrity error. Errors such as uncorrectable ECC, CRC checksum failure, or LBA tag mismatch are included in this field. Type Value Worst/Thresh Failure % Scrutiny 1 -- -- Normalized 1 --/0 -- Maybe this is related to the pci bus re ordering channels on boot

i think it marked my old intel drive (which is boot ) as bad, yes its old but pumping out writes constantly Unsure whether this is related to age or hours wear or that its the boot drive. Not very worried have system data on zfs and i feel its a false positive.

I guess my AMD Phenom(tm) II X6 1055T Processor is too old and will need to update my motherboard cpu

I dont mind tinkering but HexOS is here to simplify the homeserver life. I plan to use cady but I need time to set it up^^

Question for any of you affected by this issue, are you running HexOS in a VM or on a really old CPU? HexOS Local, which is now a requirement of HexOS, requires the AVX and SSE4.2 instruction set on your processor to function. Pretty much all modern CPUs released since 2011 have these instruction sets (there may be a few outliers that I'm unaware of), so either you are all running on really really old hardware, or you're running in a VM that is not exposing those instruction sets with the CPU model. If a VM, you can change the CPU model to "host-passthrough" or simply something that supports these instruction sets.

I have the same issue, the app try's to start serveral times, but fails. Same Version and App Version.

I just saw an update pushed to my HexOS Deck; it's showing custom apps now, so I'd expect others to get the update soon if they're rolling it out slowly to everyone.

The site https://hexoscalculator.com seems to work well. It is simple up front, but has some advanced features as well.

Seafile please

Thanks for the fix! Like other people notice it also reduce cpu usage quite a bit, this gonna help my old i5 4690k based system but like you noted the script does not seem to survive an update cuz I just updated to 25.10.3 from 25.10.2.1 and I had to redo your fix.

In case you haven't found the other thread: It's not completely on the HexOS interface, but the rollback workaround is close.

i just tested my 25.10.3 - Goldeye .with a 3050 6gb on oculink and was able to pass through the card on 25.10.3 , this is with an AMD igpu 780M , jellyfin was set to transcode with nvenc set and i set it to point to /dev/dri/renderD129 /renderd128 would have been the 780M for my configuration at least. im using a hdmi emulatator dummy plug on the 3050 I have a 5060 ti 16gb i could replace it with i could retest with jellyfin if this might help

Having the same issue Same issue, completely fresh install.

Truenas Scale switched to the open source nvidia driver which only support never cards.

I am getting the same issue and I just had to do a full reinstall.

why did they remove support?

Still broken for me.

Thanks for your Answer, i was unaware of the ZFS 80% 90%, 94% Rules.

I'm having this issue too. Looks like there is a fix on GitHub posted below, but I can't figure out how to access the app configuration files for a curated app..... really hoping I don't need to nuke my install and back up all of my photos again...... If I do I think I'll give up on the curated apps and start installing this in a docker container now that I've managed to teach myself that process. Before I do though - did anyone find a way to fix this on HexOS? https://github.com/truenas/apps/issues/4628#issuecomment-4098018533

I made a post about the same issue, they are looking into it:

It literally JUST showed up. Thanks. -- Orion

When I had local UI installed I had to log in just like the very first time I setup HexOS. It took a little while. Just long enough to make me think I was doing something wrong but the dashboard came up When I logged in I saw picture. I clicked on the word local and saw this. I am guessing it's not exactly the word that is the trigger. That just happens to be where the mouse pointer was when I clicked. I clicked on Switch to Hosted and went to the online dashboard so I started on local. Now to switch back I click the Return to Local button on the top banner. If you don't start that way I am guessing the down arrow next to your server name will allow you to go back and forth.

Im confident Ive been updated. But I see no way to change over to a local interface. -- Orion